LDPE/pmLLDPE Blend Neck-In Reduction in Extrusion Coating
Solution Overview
Problem
The introduction of a second type of polyethylene polymer into blends with low density polyethylene (LDPE) often negatively impacts the process characteristics, leading to a need for improved polyethylene blends with desired physical properties and processability in extrusion coating applications.
Innovation Solution
A composition comprising low density polyethylene (LDPE) and peroxide-treated metallocene-catalyzed linear low density polyethylene (pmLLDPE) is developed, which when blended and extruded, exhibits a reduced neck-in value, improved compatibility, and enhanced processability, allowing for increased useable product width and reduced extrusion pressure.
Engineering Contradictions & Design Principles
Engineering Contradiction Analysis
1Strength
If a second type of polyethylene polymer is introduced into blends with LDPE to improve physical properties, then the desired combination of physical properties is achieved, but the process characteristics are detrimentally impacted
Solution Approach 1:
The patent applies parameter changes by carefully controlling the melt index difference (ΔMI) between LDPE and LLDPE components, limiting it to 4.5-25. This parameter control ensures compatible rheological behavior during extrusion while allowing the blend to achieve desired physical properties. The peroxide treatment of LLDPE further modifies its parameters to enhance compatibility with LDPE, resolving the contradiction between improved physical properties and maintained processability
Solution Approach 2:
The patent creates a composite polyethylene blend system combining LDPE and peroxide-treated LLDPE in specific ratios (10-90 wt% LLDPE). This composite approach allows the synergistic combination of LDPE's processability with LLDPE's enhanced physical properties, achieving both improved strength characteristics and acceptable process characteristics that neither polymer could achieve alone
2Ease of operation
If LDPE is used alone to maintain good processability, then process characteristics are maintained, but neck-in value is higher resulting in more trim waste
Solution Approach 1:
The patent modifies the rheological parameters of the polyethylene blend through peroxide treatment of LLDPE and controlling the ΔMI between components. This parameter modification reduces the neck-in tendency during extrusion while maintaining good processability, directly addressing the issue of trim waste reduction without sacrificing ease of operation
Solution Approach 2:
The patent employs feedback by monitoring and controlling the neck-in behavior through specific blend formulations. The ΔMI parameter serves as a feedback mechanism to adjust the blend composition, ensuring that neck-in remains controlled and trim waste is minimized while maintaining process characteristics
3Strength
If the ΔMI between LDPE and LLDPE is large to achieve desired physical properties, then physical property targets are met, but blend compatibility deteriorates
Solution Approach 1:
The patent applies parameter changes by limiting the ΔMI between LDPE and LLDPE to 4.5-25, which balances two competing requirements: large enough to achieve desired physical properties differentiation, but small enough to maintain blend compatibility. The peroxide treatment of LLDPE further adjusts its parameters to enhance compatibility, resolving the contradiction between physical property optimization and blend stability
Applied Scientific Principles
This section explains which scientific principles are used to turn an abstract innovation direction into a practical engineering solution.
Function Achieved in This Case
The LDPE/pmLLDPE blend demonstrates a significant reduction in neck-in value, improved motor load efficiency, and enhanced extrusion coating properties, resulting in less trim waste and increased coating width, while maintaining or slightly improving process characteristics compared to using LDPE alone.
Implementation Method 1
peroxide-treated metallocene-catalyzed linear low density polyethylene (pmLLDPE)
Implementation Method 2
extruding a polyethylene blend as a molten resin on an extruder to form an extrusion coating
Data Source
AI summary
A composition comprising a low density polyethylene (LDPE) and a peroxide-treated metallocene-catalyzed linear low density polyethylene (pmLLDPE), wherein the composition when extruded as a molten resin displays a neck-in value that is (i) decreased when compared to the neck-in value observed when using the LDPE alone, (ii) about equal to the neck-in value observed when using the LDPE alone, or (iii) increased by <10% of the neck-in value observed when using the LDPE alone. The composition when extruded as a molten resin displays a neck-in value that is decreased by ≥5% when compared with a neck-in value of an otherwise similar composition comprising the LDPE and a metallocene-catalyzed linear low density polyethylene (mLLDPE) that has not been peroxide-treated. The composition comprises 1-80 wt. % pmLLDPE. The pmLLDPE has a melt index of ≤0.9 g/10 min, when tested in accordance with ASTM D1238 under a force of 2.16 kg.



