Lighting And Heating Apparatus TRIZ Cases

Charged particles from a corona discharge weaken moisture-absorber attraction, enabling low-temperature desorption without refrigerants or heating.

A pivoting receiving section sits below the drip edge to guide condensation outside the refrigerator without leakage, extra seals, or protrusion.

A movable refractory vault lets a wood-fired oven tune heat distribution for bread, pizza, and steaming while keeping thermal storage.

Pivoting and rotatable louvres let a switch cabinet floor pan redirect cold air to thermally stressed areas for more precise cooling.

A rotatable front control board opens access to deep-side boards in the outdoor unit, improving trial-run inspection and repair efficiency.

Dual-axis container rotation and coolant flow speed beverage chilling, improve thermal uniformity, and cut vending energy waste.

Hot-air venting from the base body lowers internal temperature, improving compressor efficiency, reducing energy use, and keeping the tub dry.

Recessed side channels and pressure orifices let a circular flap hold precise low airflow across wide pressure ranges.

A door-mounted ice maker uses cold-air ducting and a cover to preserve freezer space while keeping food odors out of the ice.

Twin cross-flow blowers and clip mounting enable top or side discharge refrigeration with lower vibration, lighter installation, and compact airflow routing.

A pivot-arm lift raises a refrigerator storage bin from deep compartments, improving access without sacrificing storage capacity.

A motorized bearinged frame lets a conventional multi-door refrigerator rotate for multi-side access while preserving structural support and visibility.

A pivoting bridge guide routes cables or pipes between the refrigerator body and door to prevent fatigue, damage, and user access.

A removable coarse auxiliary filter captures large dust before the main screen, reducing FFU blockage, maintenance, and consumable cost.

Separable planar elements and rupture zones let installers fit box finishing neatly between a safe and ceiling without cutting tools.

A spring-biased cam follower adds progressive closing torque so refrigerator and French doors shut reliably without slam noise or content disturbance.

Waste condenser heat and forced airflow speed defrost water evaporation in refrigerators while cutting space and heating pipe cost.

Valves and a level sensor regulate crisper airflow by food fullness to hold high humidity, reduce condensation, and extend produce storage life.

A door-mounted cooling layout and relocatable divider let refrigerator and freezer volumes shift while maintaining separate temperature zones.

A servo-driven swing arm pushes the refrigerator door off strong magnetic seals, reducing opening force without major structural changes.

A visually opaque vent baffle uses porous layers and one-way fasteners to protect internal electronics while preserving airflow and thermal dissipation.

A partitioned storage room uses separate warm and cold zones plus air circulation to prevent ice nucleation and hold liquids in a stable supercooled state.

Direct-mount flaps and a removable motor plate simplify off-center joist installation, wiring access, and bath fan replacement.

Reinforcing members stiffen the inner door around a subsidiary opening, enabling access to all door guards while minimizing cool air leakage.

A fiber spooler and rotary joint deliver high optical power over long distances while limiting bending loss for remote energy conversion.

Thermal dynamics from existing room and radiator sensors reveal underfed radiators and enable automatic hydraulic balancing without manual setup.

Baffles, doors, and roof sections isolate cold aisles to stop warm air recirculation and improve data center cooling efficiency.

A condenser support shaped as a watertight evaporation tray cuts refrigerator part complexity while increasing condensate evaporation capacity.

Opposed fluted impingement surfaces atomize water into small droplets while maintaining spray angle and long projection for compressed-air-free snowmaking.

A detachable partition air supply with damper and heat wire enables independent upper and lower compartment cooling while saving interior space.

Cam and cam-track whipper connections let beverage dispenser parts detach cleanly for faster cleaning with less spillage and reassembly error.

A toroid-based ground fault interrupt circuit detects differential current in an aircraft heated floor panel and cuts power before surface AC voltage hazards persist.

An insulated drive module shields the ice maker motor and gears from direct-cooling frost while preserving fast ejector operation.

Stores an unused refrigerator shelf inside the compartment by nesting base plates on multi-level supports, preserving flexible shelf height.

A two-chamber heater uses vapor-permeable separation and zeolite adsorption to heat food above 100°C without rupture, odors, or gas release.

An IR lid sensor tracks product surface temperature during rotating vacuum defrosting, enabling steam heating without surface overheating.

Non-conductive oil and a cooling manifold remove cell heat when ambient air is too warm, keeping battery modules within the target range.

A bypass refrigerant line stabilizes cold-finger temperature for clear ice making without adding a separate cooling circuit.

Molded inclined channels and a flat exchanger support improve condensate drainage while limiting air infiltration and heat loss.

Side-wall retaining projections and partial guide elements create a low-cost pull-out refrigerator shelf that runs smoothly without tilting.

Direct-contact multi-stage condensation cuts thermal resistance from incondensable gases while recovering heat for lower-cost seawater desalination.

Polygonal heated base plates connect into a reconfigurable carpet that warms specific floor areas without complex hot water piping.

Directional freezing from a cooled mold half plus continuous water circulation prevents trapped air and minerals in clear ice spheres.

A tapered vent passage, flapper, screen, and cricket-like protrusion improve gas venting while blocking water, insects, and animals.

Tufting divides the bag cavity into regions so liquids freeze more evenly, limiting projections, bag damage, and stacking problems.

Electromagnetic agitation and suction airflow speed beverage cooling in a refrigerator while avoiding freezing and improving heat exchange.

Multi-stage bubble column condensation removes water vapor while extracting non-condensable gases to improve HDH desalination heat transfer.

Mechanical agitation and forced airflow cool bottled or canned liquids faster in a removable refrigerator drawer without relying on air circulation alone.

A spring-loaded handle and meshing features let a drawer divider reposition easily while staying securely retained against accidental removal.