Partial Attachment of EMI Films on PCB Circuit Blocks

Solution Overview

Problem

Conventional methods for attaching electromagnetic interference (EMI) metal plates or protection films to printed circuit boards are labor-intensive and prone to misalignment, limiting their use in automation and mass production due to the need for precise, individual alignment of soft or small films over circuit blocks.

Innovation Solution

A method involving a shaping material with a release paper and attaching material, where the material is cut to size using a depth control tool and aligned en masse with reference points on the board, allowing simultaneous attachment to multiple circuit blocks without individual alignment, using a release paper and shaping material for EMI metal plates or a protection film module with epoxy resin glue.

Engineering Contradictions & Design Principles

VSEngineering Contradiction Analysis

1Manufacturing precision

If protection films are attached one by one to each circuit block, then alignment precision can be maintained, but manufacturing time increases and automation becomes difficult

Engineering Contradiction:
Core Design Contradiction:
Manufacturing precisionVSProductivity

Solution Approach 1:

Multiple individual protection films are merged into a single large protection film that covers multiple circuit blocks simultaneously. This allows one-time attachment operation to replace multiple sequential operations, achieving both high alignment precision through the large film's overall positioning and high productivity through simultaneous coverage of multiple blocks

Inventive Principle:
Principle #5Merging (Combining)

Solution Approach 2:

The large protection film is prepared in advance with adhesive layers and release papers attached, and the adhesive regions are pre-defined to correspond to each circuit block. This preliminary preparation enables the film to be directly applied to multiple blocks without requiring individual handling or alignment operations during the attachment process

Inventive Principle:
Principle #10Preliminary action

2Manufacturing precision

If skillful operators are used for individual alignment, then attachment precision can be achieved, but labor cost increases and automation cannot be implemented

Engineering Contradiction:
Core Design Contradiction:
Manufacturing precisionVSEase of manufacture

Solution Approach 1:

The large protection film is segmented into multiple adhesive regions, each corresponding to a specific circuit block. The release paper is also segmented with tear lines that allow operators to separate the film into individual block portions after the initial large-film attachment. This segmentation enables automated attachment of the entire film while maintaining the capability for precise individual block separation without requiring skillful manual alignment

Inventive Principle:
Principle #1Segmentation

Solution Approach 2:

The release paper acts as an intermediary between the protection film and the operator/automation system. It allows the large film to be handled and positioned as a single unit during automated attachment, then easily separated along pre-defined tear lines to expose individual adhesive regions for each circuit block, eliminating the need for skillful manual alignment while maintaining precision

Inventive Principle:
Principle #24Intermediary (Mediator)

3Manufacturing precision

If conventional manufacturing methods are used, then individual block coverage can be ensured, but manufacturing cost remains high due to inability to automate

Engineering Contradiction:
Core Design Contradiction:
Manufacturing precisionVSEase of manufacture

Solution Approach 1:

Multiple individual attachment operations are merged into a single operation by using one large protection film to cover multiple circuit blocks simultaneously. This reduces the total number of operations from N (for N blocks) to 1, enabling automation and significantly reducing manufacturing cost while maintaining accurate coverage of each block through the film's segmented adhesive regions

Inventive Principle:
Principle #5Merging (Combining)

Solution Approach 2:

The scale of the protection film is changed from individual small films to one large film covering multiple blocks. This parameter change in size and scope transforms the manufacturing process from multiple sequential operations to a single operation, enabling automation and reducing cost while the segmented adhesive regions ensure accurate positioning and coverage for each block

Inventive Principle:
Principle #35Parameter changes

Data Source

PatentUS7752746B2Method of partially attaching an additional attaching material for various types of printed circuit boards
Publication Date: 2010.07.13
  • US7752746B2 patent drawing
  • US7752746B2 patent drawing
  • US7752746B2 patent drawing

AI summary

In a method of partially attaching an additional attaching material for various types of printed circuit boards, the method attaches an additional attaching material partially onto circuit blocks after circuits of the circuit blocks are made on a flexible, rigid or mixed printed circuit board or an insulating layer is coated. The method sets an attaching material on a shaping material that covers the circuit blocks, uses a depth control tool to cut away areas not corresponding to those requiring to be attached onto the necessary circuit blocks, aligns the corresponding positions of the circuit blocks to perform pseudo attachment and pressing, and tears away the shaping material from the attaching material, so as to attach additional attaching materials properly onto the predetermined positions of the circuit blocks without requiring to attach the circuit blocks one by one, and achieve the effect of saving manufacturing time and avoiding misalignment.