Initiation circuit provides high voltage to activate charge pump, ensuring stable LDO operation during startup.
A DC-DC converter uses a signal generator to output a PWM signal with adjustable duty cycle based on input and output voltages.
Voltage ripple sensing eliminates current signal cancellation in multiphase converters, enabling stable operation across wide duty cycle ranges.
Segmented charging modes prevent load flicker while maintaining sufficient controller voltage in two-wire switches.
Multi-level charge pump circuit generates four distinct voltage levels to eliminate dedicated SMPS units, reducing manufacturing costs.
A charge pump circuit uses a clamp diode to protect the semiconductor substrate from forward current flow during voltage boosting operations.
A control circuit applies selective positive or negative offset signals to adjust power switch operation based on detected output current changes.
A dividing unit selectively divides a periodical signal to control charge pumping frequency in an internal voltage generator.
A two-stage power supply module delivers stable voltage to micro-controller circuitry in solar electric production systems.
Segmented voltage generation units with dynamic control reduce settling time and current consumption in high-speed semiconductor devices.
Dual control circuits detect HVDC and LVDC voltages to maintain stable operation when the primary energy storage device fails or is decoupled.
Comparator-controlled MOSFET transfers charge to stabilize auxiliary voltage, eliminating linear regulator inefficiencies and buck converter complexity.
A power supply circuit generates boost voltage via charge-pump operation synchronized with a charge clock signal to output stable common electrode voltages.
A step-up circuit uses voltage comparison to control switching elements and prevent rectifier conduction during faults.
A bandgap voltage reference buffer uses a feed-forward capacitor to accelerate current rise time during power-up.
A step-up converter limits starting current by monitoring output voltage and cycling a power switch to discharge the coil.
A switched capacitor voltage multiplier uses a passive recycle resistor to double output voltage without extra active circuitry.
A voltage control module and power conversion submodules form an outer voltage loop with inner current loops to enable parallel current sharing.
A step-up circuit adjusts its voltage increase rate using a reference voltage generator to match the supply voltage level.
Segmenting charge pumps with delayed clocks reduces voltage ripple and power consumption while maintaining read stability in high-capacity 3D memory.
A low dropout regulator uses a charge pump to generate gate voltages for P-channel and N-channel transistors.
A DC to DC boost converter charges storage capacitors via a parallel inductor circuit.
Dynamic clock frequency adjustment reduces parasitic power consumption while maintaining output voltage stability across varying loads.
A control device merges distinct electrical signals onto one shared line to recognize multiple inputs.
Clock signal modulation adjusts capacitor voltage difference to increase charge storage capacity in charge transfer circuits.
An internal voltage generation circuit uses oscillating signals to drive a pumping operation that produces a stable pumped voltage.
A digital controller monitors the output state to dynamically adjust gain, reducing noise without adding analog filter components.
Dynamic bias control manages voltage ripples caused by load fluctuations without increasing chip size.
A precharge controller gradually increases input voltage to protect the voltage converting device from breakdown.
A voltage detection circuit compares core and boosted supply levels to maintain a stable difference between internal voltages.
A charge recycling switched capacitor regulator synchronizes opposite-polarity gate drive signals to capture and reuse energy lost as parasitic capacitance.
A multi-stage charge pump structure uses shared capacitors between intermediate nodes to optimize voltage conversion efficiency.
A startup circuit manages I/O ring segmentation to charge an external capacitor during the initial power phase.
A UPS merges the load conversion unit with the charging circuit to supply stable voltage directly to the control unit.
Segmented flying capacitors reduce maximum voltage across switching elements, allowing smaller FETs while maintaining negative output voltage generation.
Cold backup DC/DC converters bypass faults via parallel circuits, reducing gain variation and improving conversion efficiency.
Dynamic capacitor switching in the smoothing circuit maintains stable power while reducing heat generation during high voltage operation.
An isolated switched capacitor converter uses multiple capacitors and switch sets to transfer energy without bulky coils.
Alternating charge pump halves maintain regulated output voltage, eliminating refresh interruptions and reducing power consumption.
Segmenting a charge pump into controller and booster portions reduces loading losses, doubling output voltage with fewer stages.
A power supply apparatus merges multiple voltage divider circuits into a single unit to generate arbitrary high voltages for developing and feeding rollers.
A control circuit generates trimming current signals to regulate switch on-times in multi-phase DC-DC converters.
An internal voltage generation circuit uses a comparison block to control pumping charge and stabilize output.
A boosting circuit segments charge transfer to accelerate voltage transitions in dynamic regulators.
A multi-phase power converter adjusts switching frequency to balance currents across channels.
A boost circuit increases power source voltage to the All-Fire level required by energetic fire circuits.
A boosted voltage generation circuit adjusts its boosting rate based on input voltage feedback to maintain target output levels.